Mounting A Tub
Mounting A Tub
Blog Article
We've unearthed this article on A Step-by-Step Guide to Installing a Bathtub below on the web and accepted it made good sense to share it with you on this site.
Installing a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a new one is also a reasonably tough project. If the old bathtub is conveniently available, the task can move immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have qualified on your own for the job and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might need a specialist plumber to make tube links.
This short article will help you set up a new tub in your bathroom if you have actually currently bought a brand-new bathtub as well as don't require to transform the plan of your previous water system pipes.
Your tools and material checklist should comprise the following:
Preparing for the Installment
To start with, the supporting structure supplied with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite troublesome because of the restricted gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub up until the spirit level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Switch on the water supply and also inspect all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bath tub and also examine the overflow outlet and also the typical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been used a minimum of when as this will resolve it into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making certain that the washers are in location between the tap and also the sink. Secure the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles using waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for spending some time to read our blog post. Are you aware of someone else who is curious about the topic? Be sure promote it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get A Quote
Report this page